Shaker for the collection of all types of nuts and olives Autopick GTi
The best work partner
- Undisputed leader in the shaker equipment sector (for trees from 10 to 40 cm in diameter)
- Advanced technology, mobility and adaptability.
- A single operator with a tractor is all that is needed to produce high yields.
- For the maximum pick at the minimum cost. The fruit is left clean, undamaged and ready for sale or subsequent processing.
- The machine acts directly on the tree trunk.
- Can be used to harvest both olives and all types of nuts.
- Can be adapted to shake all types of tree in all kinds of orchard.
- Full shaking coverage.
- Optional “inverted umbrella” kit.
The head is the part of the machine that transmits an excellent and soft vibration to the tree. This vibration is achieved by means of an eccentric mass with 6 adjustment positions which allow the selection of the vibration amplitude.
Adjustable clamp. Useful for trees with trunks of ≥ 8 cm up to ≤ 45 cm. The maximum aperture of the clamp is 51.5 cm.
Head integrated to receiving hopper.
Automatic gripping function before the vibration begins.
Automatic blockage of the clamps to prevent any pressure loss.
The clamp is equipped with natural rubber pads. Its shape allows the modification of their assembly position to better adapt to the surface of the different tree trunk sizes.
Protective skirt pads for a higher durability of the pads and a better care of the tree.
Both the pads and the skirt pads are available in different degrees of hardness to better adapt to all types of plantations and harvesting periods.
Adjustable gripping pressure of the head to prevent damages to the bark of the trees.
Ability to adapt to the needs and characteristics of each plantation, as long as the development of the tree allows it, ensuring a perfect vibration coverage. Adaptation of the clamp to the natural position of the trunk. Floating clamp.
Rear coupling on the tree points of the tractor.
Front coupling to the shovel.
These types of set up make possible to lift the whole unit to enable a direct download to the trailer.
Total control from the tractor cabin.
Electronic safety system for the control of the RPM and for guaranteeing the useful life of the vibration box.
Double direction vibration and with a timer for the operator to select the correct time.
Protection and control of the vibration brake.
Adjustment of the pressure for the automatic gripping of the head clamp.
Tractor: Minimum recommended power of 100 CV, standard with four wheel drive engagement.
PTO output of 540 rpm
Two circuits with independent pumps:
• Vibration : Closed circuit: Maximum flow 116 litres/minute. Maximum pressure 350 bar.
• Movements : Open circuit: Maximum flow 62 litres/minute. Maximum pressure 180 bar.
Compact and refrigerated 50 litre hydraulic tank.
It consists of a metallic box and some mobile fabric pieces in the shape of an inverted umbrella, which surrounds the tree so that when the shaker makes the nut or fruit fall, it is stored inside the hopper.
The unloading operation takes place by means of a cylinder located inside, which opens a lower trapdoor which discharges the fruits or nuts. This operation is controlled from the control box.
TARE: 560 kg
Load capacity: 350 kg
DIMENSIONS AND CAPACITIES
|Dimensions, weights and loads|
|MOUNTED FRONT LOADER *||MOUNTED REAR LOADER|
|GTi + PARK 60||GTi + PARK 110||GTi + PARK 60||GTi + PARK 110|
|(A) Total length||3.965 mm||4.195 mm||3.690 mm||4.190 mm|
|(B) Height||2.430 mm|
|(C) Width||2.300 mm||2.860 mm||2.300 mm||2.460 mm|
|(D) Length of the Receiving Hopper – PARK||2.485 mm||2.765 mm||2.485 mm||2.765 mm|
|TARE||1.375 kg||1.575 kg||1.955 kg||2.155 kg|
|MMA||1.725 kg||2.075 kg||2.305 kg||2.655 kg|
|* Hydraulic group, mounted in the rear part of the tractor (1.240 mm)|
|PARK 60||PARK 110|
|TARE Receiving Hopper||560 kg||610 kg|
|Load capacity||350 kg||500 kg|
|Receiving hopper fabric (diameter)|
|5.900 mm||6.500 mm||7.800 mm|
|Type of tire||10.0/75 15.3|